Electrical LaboratoryElectrical Laboratory
Electrical Laboratory had been aggressively widening the Scope of Accreditation yearly to cater for the industrial needs.
OUR STANDARDS REFERENCES
The 5720 A Series II is one of the latest models developed by Fluke Mfg and it is the lowest uncertainties of any multifunction calibrator anywhere.
The Wavetek 1281 incorporates many hi-tech features to enhance the application of its superior performance, such as True RMS AC Convertor & True Ohm.
Wavetek 9500 is the calibrator for Oscilloscopes up to 3Ghz.
Wavetek 9100 is the most common multifunction to cover the workload calibration of a variety of ranges including power meter, oscilloscope, temperature simulation, conductance, capacitance, XY recorder and data loggers.
The ETS High Voltage Power Supply 812 is a precision instrument and generates up to 10kV with maximum output current of 100µA which is suitable used to calibrate any non-contact electrostatic meters.
The High Voltage Dividers 100HV and 25kV Process Instruments are precision in ratio of 0.1% basic accuracy which it can measure a maximum high voltage at 100kV at 50/60Hz generated by hipot testers.
Pendulum 6689 Frequency Reference has a built in Rubidium clock with the aging rate of 1 X 10-9 Hz over 10 years is capable to calibrate user based instrument oscillators.
The Fluke 732A is a stable voltage reference for 1V, 1.018V and 10V dc voltage and it has been power up for 24 hours a day. Combination of DC Voltage Reference Fluke 732A and Standard Resistance Fluke 742A-1 and 742-10 are required to verify the characteristics of the electrical parameters in the Multifunction Calibrator.
Power Meter HP 432A with temperature compensated thermistor mounts are used to calibrate RF power meters and it can achieves an accuracy of 0.2% or 0.5uW in the most sensitive range where the error due to thermoelectric effect is reduced to negligible level.
ShibaSoku Distortion Meter Calibrator AC 128, HP 8903E Distortion Analyzer, Minato Electronics 3101 Wow-Flutter/Jitter Calibrator, Meguro MN-447A Noise Meter and Panasonic AM/FM generator and analyzer to check audio parameters in distortions, AC Level, AM &FM modulation, noise level etc.
HP 8662A, Leader 3222 & HP 8648C are the signal generators which needed as the basic requirement instrument to check the Spectrum Analyzers.
Fluke 9640 RF Calibrator has the capability to deliver a dynamic range which covers the precision power level from 24 dBm to -130dBm with stability frequency to the minimize mismatch losses, noise and errors. The output generated up to 4 GHz that sufficient to calibrate RF Power Sensor, RF Spectrum Analyzer, RF Power Meter and Modulation Meters.
The Fluke A40B Precision Current Shunt Set consists of 14 low-inductance coaxial current shunts, adapters and connectors, and a rugged transit/storage case. Designed for currents from 1 mA to 100A, the current shunts are for laboratory use in making directly measured absolute ac or dc current measurements as well as ac/dc current transfer measurements. They exhibit outstanding resistance value stability, with an excellent self-heating power coefficient, and a low temperature coefficient. With all of these characteristics combined, the shunts offer direct measurement of current from dc to 100 kHz with higher accuracy than previous commercially available shunt technology. Now precision measurements can be made in a single step process rather than by more complex traditional ac/dc transfer methods.TRACEABILITY
All our reference standards are traceable to Josephson Voltage Standard, Quantum Hall Resistance and Atomic Clock Ceasium.
(Download Traceability Chart - AC Electrical)
(Download Traceability Chart - Time & Frequency Standards)
(Download Traceability Chart - DC Voltage Standards)
(Download Traceability Chart - DC Resistance Standards)
SAMM Accreditation by Department of Standards Malaysia (DSM)
Laboratory & Site Calibration:- Sendi Mahir Sdn Bhd (Head Office)
